Jks Mfg. Control Arm Relocation Bracket, Jspec, Used to Relocate the Upper and Lower Control Arms, With 2 to 4-1/2 Inch Lift – JKS6200
$241.79
Jks Mfg. Control Arm Relocation Bracket, Jspec – JKS6200
Description
Control Arm Relocation Bracket; Jspec; Used To Relocate The Upper And Lower Control Arms; With 2 To 4-1/2 Inch Lift
Attributes:
- Compatibility: Relocate The Upper And Lower Control Arms
- Color: Black
- Material: Steel
- Estimated Install Time (Hours): 2
- Finish: Powder Coated
Features & Benefits:
- Reduced Control Arm Angles Allow The Front Suspension To More Naturally Roll Over Bumps And Grooves In The Road
- Corrects Caster For 2 Inch To 4-1/2 Inch Of Lift And The New Upper And Lower Control Arm Mounting Holes Are Precisely Positioned To Provide The Correct Caster At The Listed Lift Heights
- The Upper Control Arm Mount Provides Two Hole Positions For Proper Caster Settings Through The Full Lift Height Range
- The Proper Mounting Locations For The Installed Lift Heights Are Outlined In The Installation Instructions
- Improves The Front Drive Shaft CV Joint Operating Angles Through Full Wheel Travel And The New Geometry Increases Clearance Between The Front Driveshaft And Exhaust At Full Suspension Droop
- Brackets Are Made From Heavy-Duty 7GA Steel And Are Fully Boxed And Welded For Superior Strength When Compared To Bolt Together 2-Piece Designs
- The Heavy Boxed Construction, Fully Gusseted Lower Mount And Welded Crush Sleeves Give You Extra Confidence Both On And Off Road
- The Control Arm Correction Brackets Can Be Used With JKS Adjustable Control Arms For The Ultimate On And Off Road Performance
- The Brackets Install Inside The Factory Upper And Lower Control Arm Mounts With The Factory Hardware
- Limited Lifetime Warranty
About Product:
Improve the handling of your lifted Jeep Wrangler JK with JKS Front Control Arm Correction Brackets. Designed for use with 2 Inch to 4-1/2 Inch lift kits the brackets improve control arm operating angle to mimic or improve on factory arm angles as well as improve anti-dive during braking. Lowering the control arm mounting point slightly places the arms closer to the axle mount which corrects caster and geometry caused by the lifted ride height. Two mounting hole positions correct geometry for given lift heights. Heavy duty, 1pc, fully boxed 7GA steel brackets install inside the factory upper and lower control arm mounts with the factory hardware. The fully gusseted design you extra confidence both on and off road. For ultimate performance, Control Arm Correction Brackets can be used with JKS adjustable control arms.
Additional information
| Weight | 14 lbs |
|---|---|
| Dimensions | 16 × 10 × 6 in |
| Brand | JKS MFG. |
| Manufacturer Part Number | JKS6200 |
Vehicle Fitment
This part fits the vehicles listed below. Always confirm fitment for your exact vehicle before ordering.
This part is compatible with 104 vehicles.
| Year | Make | Model | Trim | Engine |
|---|---|---|---|---|
| Loading fitment... | ||||
Related products
-
Crown Automotive Pitman Arm – 52060056AC
Vehicle-Specific Part: Check Fitment $62.54 Add to cart Quick View -
Crown Automotive Steering Stabilizer, OEM Replacement, Single, Without Mounting Brackets/ Without Hardware, Mounts to OE Locations – 52060058AE
Vehicle-Specific Part: Check Fitment $82.30 Add to cart Quick View -
Crown Automotive Tie Rod End, Greasable, With Offset, Steel – 52060052AF
Vehicle-Specific Part: Check Fitment $154.95 Add to cart Quick View -
Crown Automotive Leaf Spring, No Lift, 4 Leaf Heavy Duty, Single – 52000707
Vehicle-Specific Part: Check Fitment $183.50 Add to cart Quick View